Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

Big box joints in laminate

I posted a cpl of piccies in ABPW. So those of you lucky enough to have access, go see them, I think it is a creative id...
3 comments posted 21yrs
posted by design
3 comments posted 21yrs posted by design

FAO FISHING BOATS

http://www.fao.org/documents/show_cdr.asp?url_file=/DOCREP/003/W7260E/W7260E00.HTM I believe these are meant for develo...
0 comments posted 21yrs
posted by Jakofalltrades
0 comments posted 21yrs posted by Jakofalltrades

P-C 3700L Miter Saw

You can get the new PC 10" twin laser miter saw for $174.00 at amazon.com. Their price is $199 with a $25 coupon code an...
1 comments posted 21yrs
posted by oconnors
1 comments posted 21yrs posted by oconnors

Dewalt DW928K-2 14.4 Drill/Driver - Opinions?

I have a B&D 12V that I'm ready to recycle in the garage sale, noticed my local Lowe's has the model shown above on cle...
5 comments posted 21yrs
posted by affemensch
5 comments posted 21yrs posted by affemensch

Where's Home Depot

Looked at the thread about the Ryobi OSS on sale at HD, and decided to see if the closest one to me (about 10 miles) ha...
47 comments posted 21yrs
posted by Jakofalltrades
47 comments posted 21yrs posted by Jakofalltrades

Re: some project

> Here are two project that I have completed out of solid oak a book case and > a bathroom cabinet > > > begin 666 Shor...
7 comments posted 21yrs
posted by DaveHinz
7 comments posted 21yrs posted by DaveHinz

Hot Dawg Heater Questions....

Ok, difficult question, I just ordered the Hot Dawg HD45 45,000 heater for my garage. It's an oversized two car garage,...
13 comments posted 21yrs
posted by sysadmin
13 comments posted 21yrs posted by sysadmin

Tablesaw Blade Alignment

I struggled for quite a while to try and get the blade adjusted parallel to the miter slot. Thinking I had a Delta Unis...
6 comments posted 21yrs
posted by nekias
6 comments posted 21yrs posted by nekias

Tricky cut - how would you make it?

I am making a dresser which will be the mate to one I already own. Each drawer has mitered oak trim on the front with t...
9 comments posted 21yrs
posted by REMOVE-dicksnyder
9 comments posted 21yrs posted by REMOVE-dicksnyder

limewash as wood preservative

Has anybody tried a limewash on exterior timber furniture. That is on previously untreated timbers.
0 comments posted 21yrs
posted by david
0 comments posted 21yrs posted by david

OT - hammer drill newbie question

I was given a box of some no-name hand tools by a well-meaning friend. Among the tools is a no-name drill that is suppo...
9 comments posted 21yrs
posted by no_spam
9 comments posted 21yrs posted by no_spam

Are all *new* stanley planes equal?

One of the dealers I frequent carries several lines of hand planes. Since record went belly-up, he began carrying Stanl...
6 comments posted 21yrs
posted by wrobertdavis
6 comments posted 21yrs posted by wrobertdavis

OT Buying a windsor chair set

OK, I'm at least man enough to admit the task of making/finishing 6 windors is out of my reach at the present time... I...
5 comments posted 21yrs
posted by msschmenk
5 comments posted 21yrs posted by msschmenk

CHISEL HOLDER

http://www.shopsmith.com/ownersite/proj_articles/chiselholder/index.htm JOAT Some is good, more is better, too much is j...
0 comments posted 21yrs
posted by Jakofalltrades
0 comments posted 21yrs posted by Jakofalltrades