Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

How to install drawer fronts to drawers?

I'm workin on a built-in entertainment center and made a couple (12) of drawers without fronts. Now I'm contemplating w...
22 comments posted 21yrs
posted by mare*Remove*All*0f*This*I*Hate
22 comments posted 21yrs posted by mare*Remove*All*0f*This*I*Hate

Finishing question

I'm looking for a tough finish for a childs' dresser. The problem is that because it's still rather cold here (35F) I r...
5 comments posted 21yrs
posted by bw_hntr13
5 comments posted 21yrs posted by bw_hntr13

recomended glue for hardwood flooring

hey guys , starting to lay my 3/4 " birch floor tomorow and will be doing the stairs early next week , i was thinking o...
0 comments posted 21yrs
posted by f_harwood
0 comments posted 21yrs posted by f_harwood

Can't Find a J-roller for Laminate

I've been to all the hardware stores and flooring stores in the area, but nobody sells a simple J-roller. I will be app...
6 comments posted 21yrs
posted by nekias
6 comments posted 21yrs posted by nekias

tough clear lacquer

just painted some toys with cheerful emulsion paint. what is the hardest and most easily applied clear lacquer or coati...
6 comments posted 21yrs
posted by blue.star77
6 comments posted 21yrs posted by blue.star77

Re: Table Saw Woes

could be the start/run switch is not going from run to start position. Some times the little springs that pull it back...
5 comments posted 21yrs
posted by boots
5 comments posted 21yrs posted by boots

Source for spare part for Incra Jig

Yes, I googled. Looking for the end piece of the stop that was an add on to a miter guage track.... JOE
2 comments posted 21yrs
posted by JoeTaxpayer
2 comments posted 21yrs posted by JoeTaxpayer

Angled mortise and tenon joints

I'm making some plant stands which will have legs splayed out at 7.5 degrees from vertical. There are two sets of horiz...
3 comments posted 21yrs
posted by markn
3 comments posted 21yrs posted by markn

Finishing woes

Yesterday I applied a concoction of 3 stains: 2 Varathane and one Zar, to get the color I needed. My typical procedure...
0 comments posted 21yrs
posted by David
0 comments posted 21yrs posted by David

Re: OT Humor: Woodworkers exercise routine

>Darn, I thought I was getting plenty of exercise just by pushing my luck. "This company does not have a work-out progr...
1 comments posted 21yrs
posted by bonomi
1 comments posted 21yrs posted by bonomi

Almost dropped the phone.

I called Delta today to see about getting a manual for my recently acquired 46-700 lathe. Naturally they have an automa...
6 comments posted 21yrs
posted by LRod-removethispart
6 comments posted 21yrs posted by LRod-removethispart

Looking for a design

This might not even be mathematically possible, I would like to build a wooden puzzle, a pyramid. One of the type where...
2 comments posted 21yrs
posted by runaway
2 comments posted 21yrs posted by runaway

TS fence upgrade?

Hello, everyone. I'm a relative woodworking newbie, who's been lurking here for a while, waiting til I had a burning qu...
0 comments posted 21yrs
posted by f.ali
0 comments posted 21yrs posted by f.ali

TS fence upgrade?

Hello, everyone. I'm a relative woodworking newbie, who's been lurking here for a while, waiting til I had a burning qu...
6 comments posted 21yrs
posted by f.ali
6 comments posted 21yrs posted by f.ali