Woodworking Forum

  1. Home
  2. Woodworking Forum
51629 Threads Posts
to

Worth reading in Woodworking Forum

Hitachi KM12SC Amazon for $88 with code

OK. The price is too good to be true (for long). What's the highs and lows about this router. Special is only on till t...
6 comments posted 20yrs
posted by njtrout_2000
6 comments posted 20yrs posted by njtrout_2000

best glue for new chair joints?

Hi, I am building 4 mission style high chairs in red oak for the kitchen counter. There are about 50 mortise and tenon...
5 comments posted 20yrs
posted by padlnjones
5 comments posted 20yrs posted by padlnjones

Is my TS broke?

I have a Jet contractor saw that recently started vibrating. I can see the belt bouncing when the saw is running. I had...
7 comments posted 20yrs
posted by NunyaBiznas
7 comments posted 20yrs posted by NunyaBiznas

uneven boards.

I'm making a side table. The top is Queensland Maple (a cabinet grade hardwood) I joined three 200mm (8"?) boards toget...
27 comments posted 20yrs
posted by blankotanko
27 comments posted 20yrs posted by blankotanko

Installing Joists

Hi, Im renovating a workshop and have to replace 4 joists. One end will sil just below ground level, in eatch essential...
3 comments posted 20yrs
posted by mike
3 comments posted 20yrs posted by mike

New over old (laminate)

Greetings, Does anyone have experience applying new Formica/Wilsonart laminate over old laminate using waterborne conta...
14 comments posted 20yrs
posted by Gringo
14 comments posted 20yrs posted by Gringo

Inca 410 questions

I have an Inca 410 jointer/planer that I purchased used a few days ago. The manual suggests Waxilit for the top, to mak...
0 comments posted 20yrs
posted by cgallery
0 comments posted 20yrs posted by cgallery

Starrett Planer/Shaper Gauge Manual?

Anybody have a manual for one? Or know where I can get one? I bought an old #599 on eBay and it woud be nice to have a...
1 comments posted 20yrs
posted by jjinatx
1 comments posted 20yrs posted by jjinatx

Lattice fence and gate

Hi guys Just wondered if anyone could suggest how I can make an angled joint into a square 4 x 4 post? I will be having...
0 comments posted 20yrs
posted by ericbrighteyes
0 comments posted 20yrs posted by ericbrighteyes

Dad is selling old tool chest with tools

My Dad wants to sell an old wood toolchest that has many, many tools with it. This I believe is a patterns makers chest...
22 comments posted 20yrs
posted by wayneREMOVETHIS
22 comments posted 20yrs posted by wayneREMOVETHIS

Can you make a plunge cut with a router?

I need to make a shallow (1/2" to 1" deep) depression ( about 2"x2") in a solid block of wood. Can I make a plunge cut...
3 comments posted 20yrs
posted by ppdavid.nospam
3 comments posted 20yrs posted by ppdavid.nospam

drill press advice

I'm looking for a benchtop drill press. The Delta 300 series looks good but so does the Craftsman. Any suggestions? Than...
6 comments posted 20yrs
posted by joedegrande
6 comments posted 20yrs posted by joedegrande

My next bit of finishing ignorance

I built a shelf unit. I've been trying to match a color more or less. I think I have that part on track. I've been mixi...
4 comments posted 20yrs
posted by gdguarino
4 comments posted 20yrs posted by gdguarino