Carpentry - Homeowners' Hub Questions and Answers

listing options: FAQ |  answered |  unanswered |  recent |  oldest 

Hanging an awkward heavy cupbaord

michael timberlake's Avatar (by Gravatar) by michael timberlake in  Carpentry 

Hi I'm no DIY expert but I usually manage to bumble through but this has me stumped. I have  ... read more »

This question has been answered 1 time. Add your answer today!

Hornets

Phyllis's Avatar (by Gravatar) by Phyllis in  Carpentry 

How can I get rid of very large hornets living under the cedar shingles of my house  ... read more »

This question has been answered 1 time. Add your answer today!

Finish nail gun

K D G's Avatar (by Gravatar) by K D G in  Carpentry 

I have a 15 gauge 35 degree finish nail gun can I use 15 gauge 34 degree finish nails without any damage  ... read more »

Deck footing heaving

Anonymous's Avatar (by Gravatar) by Anonymous in  Carpentry 

Hi I just recently purchased a home and noticed that since the frost has thawed one of my deck posts/footings  ... read more »

Do you have any air pockets when filling with the integra glue?

Anonymous's Avatar (by Gravatar) by Anonymous in  Carpentry » Glue »

We have tried to use intergra glue for inlaying but everytime we struggle with air pockets. Then we refill  ... read more »

Can I replace lp siding with hardy board in the rain?

Anonymous's Avatar (by Gravatar) by Anonymous in  Carpentry 

No further details provided  ... read more »

what is the weight ratio of 1/2" plywood cdx

Anonymous's Avatar (by Gravatar) by Anonymous in  Carpentry 

No further details provided  ... read more »

Where do I buy plywood supplies nearby GLendale AZ 85304

Anonymous's Avatar (by Gravatar) by Anonymous in  Carpentry 

No further details provided  ... read more »

How much weight per foot will a 3/4 plywood decking support placed on 2x8 joist 24" centers 8' long

Anonymous's Avatar (by Gravatar) by Anonymous in  Carpentry 

A piece of plywood 3/4 on 2x8 joist on 24 inch center 8 feet long what per sq. foot weight can it hold?  ... read more »

how far will a 4by12by 20 feet header span..

Anonymous's Avatar (by Gravatar) by Anonymous in  Carpentry 

No further details provided  ... read more »

is it recommended using a 3/8 RTD sheathing over a three quarter cross bracing

Anonymous's Avatar (by Gravatar) by Anonymous in  Carpentry 

Is it okay to put a 3/8 RTD sheathing Over a three quarter Cross brace Subfloor  ... read more »

What size drill bit required for anchor?

Jack of no trades's Avatar (by Gravatar) by Jack of no trades in  Carpentry 

I am trying to hang a small rack. It says to drill a 3/32" pilot hole into the stud. However I am  ... read more »

Do you guys draw up design plans for small outdoor structures?

Maggie's Avatar (by Gravatar) by Maggie in  Carpentry 

I volunteer for an animal shelter and we are in need of outdoor cat habitats. The ones currently in  ... read more »

red resart button wont respond on sears craftsman 10" Mod. Num. 113.19770

Anonymous's Avatar (by Gravatar) by Anonymous in  Carpentry 

No further details provided  ... read more »

This question has been answered 1 time. Add your answer today!

Garage shelving .750 thick plywood 30D" x 36"W

old_dog's Avatar (by Gravatar) by old_dog in  Carpentry 

I have ball bearing glide supports used in office furn. file cabinets. Normally loaded with blocks of  ... read more »

Looking for a parts listing on a Haubold RN90 Framing nailer 22 Degree 3 1/2 st

Butch's Avatar (by Gravatar) by Butch in  Carpentry 

3 1/2 streight line nails full heads Need a parts listing and a place to buy the parts..?  ... read more »

top of a buffet I am redoing is peeling some kind of thin paper wood,

Anonymous's Avatar (by Gravatar) by Anonymous in  Carpentry 

The buffet top is covered with some type of paper wood very thin I want to cover it with something.  ... read more »

Is there a type of drawer slide that stops or locks at any position?

Anonymous's Avatar (by Gravatar) by Anonymous in  Carpentry 

Looking for a drawer slide that will hold a drawer open at any position--like you would want on a keyboard  ... read more »

Ballet rail bracket spacing?

Anonymous's Avatar (by Gravatar) by Anonymous in  Carpentry 

Hi Iam looking to see if there are any recommendations on spacing of brackets of a wooden handrail that  ... read more »

listing options: FAQ |  answered |  unanswered |  recent |  oldest 

HomeOwnersHub.com is a website for homeowners and building and maintenance pros. It is not affiliated with any of the manufacturers or service providers discussed here. All logos and trade names are the property of their respective owners.