Latest threads in Woodworking Forumshow only best voted threads
Subject | Author | Posted | Replies | |
---|---|---|---|---|
|
Modern Marvels - Glue - Lumberyard
Glue is on Modern Marvels at 7'm tonight, east coast time. Then at 8pm The Lumberyard. I've seen both, several times each, but plan on watching both again; I figure they're that interesting. JOAT What...
1
|
16 years ago
|
1 | |
|
You can Work easier
404 - Not Found
—
|
16 years ago
|
— | |
|
Celtic Designs
When my wife and I got married a not quite a year and a half ago, while moving her in with me the music stand on her piano was damaged by the movers. My next project is to make a new one, and I don't...
15
|
16 years ago
|
15 | |
|
Trouble setting up new table saw
Recently got a Powermatic PM2000 cabinet saw. Yesterday I set the miter slot to blade and miter slot to fence parallel adjustments using a dial indicator. I was able to get both to within .002". So...
96
|
16 years ago
|
96 | |
|
Looking for plans for a planer sled
Hi, I'm looking for plans for a planer sled. I'm trying to mill some wood that is too large for my jointer. Can't seem to find any online. Thansk Alex
2
|
16 years ago
|
2 | |
|
OT - Neander Limo
OK, some of you didn't think much of some of the vehicles I'm interested in. Questions on gas mileage, and so on. So found this one is for all of you worried about pollution, low gas mileage, and all...
3
|
16 years ago
|
3 | |
|
Re: Very Funny Story ....A STORE THAT SELLS HUSBANDS .. Must Read....
"avtar" seeks to lure you to some spammy site, no doubt... ... what must be awaiting me further on?" So up to the sixth floor she goes. The sixth floor sign reads: Floor 6 -You are visitor 3,456,789...
—
|
16 years ago
|
— | |
|
miters
Hi All, I am fairly new to woodworking and am trying to aquire some new skills... I am in the middle of making an oak framed mirror, I have the timber thicknessed and planed and am about to embark on...
7
|
16 years ago
|
7 | |
|
What is it? CXCVIII
A new set has just been posted: I mentioned a couple weeks ago, please don't send any email to the account that I use to post here on the newsgroups, it still doesn't receive any incoming mail,...
30
|
16 years ago
|
30 | |
|
Masaschi's Foolproof Wood Finishing
Anyone here read it? Comments, opinions? ROY!
2
|
16 years ago
|
2 | |
|
SEMI OT - Finally found the 'ultimate' pickup of my dreams
This covers all my vehicle needs perfectly - basic transportation, wood hauling, etc. is life without challenge and a constant stream of new humiliations? - Peter Egan
24
|
16 years ago
|
24 | |
|
DRAWING A BOARDER AND TITLE BLOCK
I AM JUST LEARNING SCETCH UP AND WANT TO TEACH IT TO MY TECH STUDENTS I NEED TO DO A BOARDER AND TITLE BLOCK AS A TEMPLATE AND AM HAVING DIFFICULTIES
28
|
16 years ago
|
28 | |
|
OT - Need Vehicle Input
I think I'd like to have one of these, for hauing wood. Anyone here have one? If so, how does it handle? JOAT What is life without challenge and a constant stream of new humiliations? - Peter Egan
14
|
16 years ago
|
14 | |
|
where to find bamboo
hello, I am looking for bamboo boards to make sushi sets (roughly 12" by 8") peices in 3/4 thikness... does anyone know where to find something like that? near boise would be even better! thanks,...
5
|
16 years ago
|
5 | |
|
Sharpening Carbide - ScarySharp?
I see that DMT has an 8000"mesh" diamond stone and was wondering if I could use that to get my router bits "scary sharp", or at least sharper than how they come from the factory. Any thoughts? JP
5
|
16 years ago
|
5 |