Latest threads in Woodworking Forumshow only best voted threads
Subject | Author | Posted | Replies | |
---|---|---|---|---|
|
Tools For Sale in NJ...
Not mine... Someone handed me a "blurb" with a name and phone number and said the guy had some tools. No clue what they are or if the prices are fair... But if you want to call, feel free: Joe -...
—
|
16 years ago
|
— | |
|
Stair railing estimates
I would hesitate to answer unless I knew what material and how far this thing is going - 3 risers or 20? with a wrap around porch? Cable systems, glass, steel? Will this need to pass the 4" ball rule?
12
|
16 years ago
|
12 | |
|
Cigarette burns - any fixes?
Suggestion. Look all over them for a manufacturer's mark--if they're that good there's very likely such a mark somewhere. If they're still in business contact them for advice.
7
|
16 years ago
|
7 | |
|
Identifying finish - need help
How can I identify the finish on a piece of furniture? I inherited a couple of pieces of oak furniture made by the Sumter Cabinet Co. I did a web search and they're still in business, but could find...
3
|
16 years ago
|
3 | |
|
Unfortunate Attempt To Remove A Dent - What Now?
| Hi, | | I made a error and could use some opinions. | | A table top under construction fell over and got a tiny nick. | The water and heat trick didn't remove it. I didn't want to | fill it or leave...
23
|
16 years ago
|
23 | |
|
repairing charred cabinet door
Hello, I have a cabinet door that was slightly damaged in a fire. The door is only blackened at the bottom and bottom part of the front of the door. The door is intacted and in great condition...
3
|
16 years ago
|
3 | |
|
OT: Too funny.
The CNN Political Ticker is the hottest destination for the latest political news with dispatches, behind-the-scenes reports, and expert commentary, 24-7. For the latest political news from CNN's Best...
3
|
16 years ago
|
3 | |
|
Ebonizing Maple - Follow Up
First, thank you to everyone for their genuinely helpful ideas. I tried most with varying degrees of sucess. Pics and my commentary posted in abpw. Joe C.
—
|
16 years ago
|
— | |
|
Tersa knives in Australia
Hi guys, My company will be providing Tersa blades for the Australian market in a few months time. * Knife change in seconds * Knives are clamped by centrifugal force so no screws * No knife...
—
|
16 years ago
|
— | |
|
Recommendations on starter set of hand planes...
I keep seeing the experienced gurus here talk about the miracles they can do with hand planes (along with the high prices one can pay for some of the best :). Unfortunately, I just have a borg-quality...
19
|
16 years ago
|
19 | |
|
What type of TS blade to "resaw" QS White Oak?
I need to split some 4/4 x 2" QS White Oak to make some thin stiles approximately 3/8" thick (minus half a saw kerf) for a paneling system. The exact finished thickness is not important but I do need...
9
|
16 years ago
|
9 | |
|
outlet/low voltage in fireplace mantel?
Hi Bob, I built a house from the ground up and have a TV over the fireplace. In NY state the fire code enforces the use of steel studs behind the drywall above a fire place. Steel stud framing has...
13
|
16 years ago
|
13 | |
|
plywood or presswood
It looks like you *really* wet it down. My best advice is... STOP DOING THAT As thick as that is - and as wet as it appears you have made it - it is going to take weeks if not months to dry out and...
24
|
16 years ago
|
24 | |
|
Bandsaw blade drifts
I suspect I need a new blade but I figured I'd post my experience for input. This morning my bandsaw blade was tracking fine. Later I cut some cardboard for the trash. Immediately after that, my blade...
24
|
16 years ago
|
24 | |
|
Need Some Ideas
Some time back I told how I used my hand power plans to round out stock in my wood lathe. Had planed a side of a couple of chunks of 2X4, glued them together, then turned 3 different weight carver...
8
|
16 years ago
|
8 |