Latest threads in Woodworking Forumshow only best voted threads
Subject | Author | Posted | Replies | |
---|---|---|---|---|
|
sanning veneer
I just cut some lacewood to make some "veneer" (it's not really, but that's the best way to describe it). The problem I have is how to now sand out the marks left by the band saw. The pieces are about...
16
|
15 years ago
|
16 | |
|
5 year-old latex paint.
Not directly related to woodworking, but I am hoping to paint some stuff on the outside of the house with a couple of gallon of Benjamin Moore Exterior Latex of a particular colour which I have in...
17
|
15 years ago
|
17 | |
|
Rubbertized finish
The step on my F150 (which gets driven a lot less these days) has some rust on it. I'm going to dremel off the rust and put some primer on it, but the step has a rubberized finish. Where kind of...
5
|
15 years ago
|
5 | |
|
route jig for thickness planing?
Hi, I'm a bit of a newbie to this, but am starting a project that needs 1/2 inch stock and need to plane my 3/4 inch stock to thickness. I'm not fortunate enough to have a thickness planer and I suck...
2
|
15 years ago
|
2 | |
|
Citizen Disney Watches - Citizen Watches Minimum Price
Citizen Disney Watches - Citizen Watches Minimum Price Hot Watch : Watches : Disney Watches : Disney Watches All Products : Citizen Eco-Drive Mickey Mouse Mens Watch BM8084-58C : Eco-Drive Disney...
—
|
15 years ago
|
— | |
|
Connecting sandpaper roll into belt
Hi can anyone tell me how to connect sandpaper that are sold in rolls into a belt for belt sander use? Whats the adhesive used? my orignal seem to be connected at the edges about 0.8cm at the ends...
3
|
15 years ago
|
3 | |
|
OT: Spots
"Every time I close my eyes, I see spots." Friend: "Did you see a doctor?" "No.. just spots."
—
|
15 years ago
|
— | |
|
putting an edge on MDF?
I'm planning to use some Neatform Bendy MDF to create a short curved wall in my apartment. What tool would I use to put a 45-degree edge on the back side all along an 8-foot panel?
9
|
15 years ago
|
9 | |
|
Confirmat Drill bit
Hello everyone, I am updating my closet and using a prebound Formica on particle board. (Similar to melamine with a wood grain pattern) I was told the best thing to use for joining two pieces together...
8
|
15 years ago
|
8 | |
|
routers
Anyone know about Freud routers(Ft3000VCE). I have chance to buy one at an coming estate sale. tia gym
1
|
15 years ago
|
1 | |
|
Story about Red Oak prices on NPR this evening
What goes around comes around, fashion-wise, so in 20 years or so the demand for oak will go back up - and if fuel prices stay high enough and the wages in China go up, it will be economical to build...
2
|
15 years ago
|
2 | |
|
Wood Comparision Chart
There are a number of sites on the web. The link below is one for common domestic lumber. They also have a page for exotic lumber. Click on the hardwood's name to see its characteristics.
4
|
15 years ago
|
4 | |
|
OT: Anyone use BHG Home Designer Pro 7 or 8?
Last night I watched Swingman draw a room with 2x6 studs 9' tall with windows and doors in about 2 minutes using Google Sketchup.
11
|
15 years ago
|
11 | |
|
Outboad Motor Stand
I want to build a Outboard Motor Stand to store and repair my 4 HP engine when needed. At this time, I do not have any set plan. I would appreciate any tips, ideas or plans. TIA Denis M
1
|
15 years ago
|
1 | |
|
92" BandSaw Blade
Timberwolf to name one, and probably a few local shops in your area can make a blade to any length you want. Typically blades are made and sold by the inch.
7
|
15 years ago
|
7 |