Latest threads in Woodworking Forumshow only best voted threads
Subject | Author | Posted | Replies | |
---|---|---|---|---|
|
Using a Senco SC2 corrugated fastener gun
I picked one up on eBay for cheap and am curious about best use practices. If I'm joining 3/4" stock should I be using the shortest fasteners - the 1/4" ones, or can I use as big a one as won't shoot...
5
|
14 years ago
|
5 | |
|
Question for anyone owning a Grizzly G0555 14" bandsaw
I just picked up my bandsaw at the local trucking depot but have not assembled it yet. I also ordered and have received the riser block kit. I assume when I assemble the bandsaw and stand I should...
12
|
14 years ago
|
12 | |
|
Carbide hole saws
Every time that I've used a hole saw, it's been a pain in the ass. They're fine on thin Pine, but that's about it. Even brand new ones will burn and stall my drill. Are carbide hole saws "much"...
13
|
14 years ago
|
13 | |
|
Glass wheel for Worksharp WS2000
I've recently picked up a Worksharp WS2000 sharpener and like it so far, but I noticed on the sandpaper that the areas of the wheel that don't have direct contact with the plastic wheel (due to it not...
3
|
14 years ago
|
3 | |
|
Gibson guitars raided by feds
guitars raided in federal rosewood investigation Leading global guitar maker Gibson says it is co-operating with US federal agents following a raid on its Nashville factory as part of an investigation...
4
|
14 years ago
|
4 | |
|
Cordless Drill Torque Ratings?
Folks, I'm thinking of using subject drill in an unusual application, turning a sailboat winch to hoist about 40 lbs; occasional use, not a steady workload - and a right-angle drill. I've read where...
20
|
14 years ago
|
20 | |
|
OT Assorted Multi Master Tools on sale on Amazon.com
Fein $209.00 Thought you might want to know
—
|
14 years ago
|
— | |
|
Good price right now on Porter Cable PC180DK-2 cordless drill
Believe this is the drill I bought a few months back. If it is, its a piece a junk. The reverse and forward switch stopped working after only 3 weeks on the job. I took it to a service center and they...
4
|
14 years ago
|
4 | |
|
Drawer slide recommendation ?
And just to clarify. The slides are smoooth all along their travel. It is just at the very end, the last 1/8", as you are pushing the drawer fully closed, that the *friction catch* comes into play....
45
|
14 years ago
|
45 | |
|
What is it? Set 311
or fireplace. 1778: Looks like a big bench dog. 1779: A trap. Something small can get in, but not out. 1780: Ashtray of some sort. I recall that my parents once had one like this. 1781: An old...
18
|
14 years ago
|
18 | |
|
Looking for help from the wRECk on slide outs for blind cabinets
I am looking for plans to create a "Magic Shelf" (a slide out that slides the blind corner when main cabinets shelves are slid out of the way) or something similair. There are several professional...
—
|
14 years ago
|
— | |
|
OT - Nancy and her chauffeur
This one is making the rounds again, and I still like it. Janet Reno was the subject the last time I heard it..... Nancy Pelosi was touring the countryside in a chauffeur-driven car. Suddenly, a cow...
—
|
14 years ago
|
— | |
|
O/T: Retiring to Alaska
I first heard that one from Methuselah's great-grandmother, but it was set in the wilds of Scotland, and the punch line was ""Nae, yeer fine just the way ye are - It's jest you and me, laddie." Scott
2
|
14 years ago
|
2 | |
|
square drive screws - extinct?
I have bought them at Ace Hardware during the past year. RVs' also use a lot of them so you might check a service department for their source. RonB
25
|
14 years ago
|
25 | |
|
Free 3 Phase Unisaw Motor
Sometime ago, I bought a used Unisaw, but can't use the 3 ph motor. Offering it for free, other than shipping costs. If you're in the south Louisiana, Houston area or somewhere a bit north, shipping...
1
|
14 years ago
|
1 |