Latest threads in Woodworking Forumshow only best voted threads

Subject Author Posted Replies
 
TR-8 Router collett chuck (hitachi European model part number: 971857z)
Hi All. A bit of a long shot...has anyone out there got either a spare or know of access to a replacement collett and chuck for my router? Labelled no.17 in the parts guide at Thanks a mill'. With...
2
2
 
Rockwell 4676 router manual? I need to replace the collet to a 1/2" collet and would like to know what size would the replacement be or if I can use a different brand collet??
Where can I get a Rockwell 4676 router manual? I need to replace the collet to a 1/2" collet and would like to know what size would the replacement be or if I can use a different brand collet??
 
Oneida Super Dust Deputy XL 6”
Wondering if anyone has installed this? Is it an efficient cyclone when paired with a high merv cartridge filter? Planning on hooking up to a 2 hp single stage.
25
25
 
Festool Cord/hose clips
For anyone with a Festool dust collector, these hose clips work very well. I've noticed a lot of people are putting their 2-D printers to good use. <> Innovative Helical Design - Grips Hose Ribs....
2
2
 
The Platforms For My Vehicle Are Complete - (Carpeted 2 x 4's)
Over the past 4 generations of the Honda Odyssey, the floor has been getting more and more bumpy and unlevel. It gets harder to load stuff with each new 5 year cycle. This is the interior of my 2017...
157
157
 
Ping Sonny: How do you carpet a 2 x 4?
I need to wrap carpet around the end of a 2 x 4 that is attached to a sheet of plywood. Take a look at the images below. following is what I trying to get to, but without the bulky seams. (It looks...
39
39
 
To Drby Dad
So if you felt I called you a troll, I apologize.
90
90
 
Plywood: Is MDO Always Cheaper Than Sheathing?
I just bought a sheet of 1/2" Douglas Fir MDO Plywood at Lowes. Actual thickness: 0.484. The entire stack (50 sheets?) was flat as can be, no gaps between sheets. $73.98 My other choice was 1/2"...
13
13
 
Rebuilding Outdoor Bench - Wood Suggestions?
It's time to rebuild the bench I inherited from my Grandparents. It was around when I was a kid, so it's gotta be at least 70 YO. Probably a lot more. I want to do it justice. The slat's are just...
16
16
 
X5 replacement motor?
Having trouble finding a motor for my x5. It came with a 3 hp . The ones I’ve found on eBay from lesson seem to have the slotted adjustment on wrong side. Mounted in saw the slot is on left side...
14
14
 
Can I use a Laguer Spray under/over Spar Urethane?
rec.woodworking is still very active; crossposted.
2
2
 
removing old damaged insert nuts
Any useful tips are welcomed. One arm came loose on a teak armchair - fastened by 2 quick-connect bolts into 2 insert nuts. < 1/4 - 20 or a metric equivalent > The insert nuts had deteriorated over...
34
34
 
Hitachi F-1000A jointer planer height adjustment gears do not engage
I am facing a strange issue after I disassembled and reassembled the central height adjusting threaded rod. Removed the stripped nut and lock nut on the top, rethreaded the top part of the rod using...
 
Help. Hitachi F-1000A Cannot lower the planer table
Hi Fallow Woodworkers: I have an old Hitachi A-1000A jointer-planer combo machine. I am facing a strange issue. The planer bed or table can be raised with reasonable efforts. However, it cannot be...
13
13
 
New Woodpecker Exact 90 Miter Gauge - do you believe it? (2023 Update)
Woodpecker has announced a new product called Exact-90 Miter Guage. Its claims to fame include dead square 90 degree cuts, 45" fence range, and 24" stock width handling on a 10" table saw. The latter...
21
21