Latest threads in Woodworking Forumshow only best voted threads
| Subject | Author | Posted | Replies | |
|---|---|---|---|---|
|
|
Spiral cutting router bits
Please excuse the naive question... but I read about spiral cutting router bits hither and yon. But what is the upside? Downside? Are these plunge bits for the router table? And where's the best place...
8
|
17 years ago
|
8 | |
|
|
Table saw 55 deg chamfer question
I have a 5.5 x 5.5 x 1.5 piece that requires a 55 deg (from the vertical) x .75 chamfer on all four sides of the large periphery. How can I do this on a table saw with a 10" blade that only goes 45...
14
|
17 years ago
|
14 | |
|
|
size &/or "Wonder" wheel, grinding disk, or blade on TS for safe cutting of acrylic light shield plastic
again...
9
|
17 years ago
|
9 | |
|
|
what is best way to glue small sculpture
Hi-I am refinishing a small Jesus figure from a crucifix. It is carved out of cedar and both arms have seperated from the body at the shoulder. There are small spike type things in each arm that have...
9
|
17 years ago
|
9 | |
|
|
Cutting hole in tile
I'm building a cabinet the will support a bathroom sink, one of those round dingies that sits on the cabinet. The cabinet top will be ceramic tiled and I need to cut a four inch square hole in the...
11
|
17 years ago
|
11 | |
|
|
saw blade
I have a Bosch 4000 ts. What would you suggest for a blade to make a smooth cut for picture molding? Patt
1
|
17 years ago
|
1 | |
|
|
veneer to sell
I have this veneers to sell: cherry, oak, maple, makore figure, walnut, beech, mahogany. I have many sequence sheet. Sheet size: 6" to 25" long x 3" to 15" wide. If you are interested, I can send a...
1
|
17 years ago
|
1 | |
|
|
New JET or Pioneer Cabinet saw?
Which would you buy a Jet or Pioneer Cabintet saw. Thanks Kevin
1
|
17 years ago
|
1 | |
|
|
PC Hammerdrill and oil
Hello All, I have recently purchased a "used" Porter Cable PC7751 hammer drill. I put the used in quotes because I purchased it from a person who never once used it - as in the power cord is still...
—
|
17 years ago
|
— | |
|
|
Shelf standard increments...
So I finally got my order from Outwater Hardware, no thanks to f'UPS pathetic delivery. Among the items I ordered were the SUP-5030-Q-CL "lock down" shelf clips for 1/4" holes. Now these shelf clips...
—
|
17 years ago
|
— | |
|
|
Any Moldingknives.com users?
Has anyone here every ordered their Designer Knife Series? did it turn out to be something you used all the time or something you never get out of the box? The designer knife series is a set of about...
—
|
17 years ago
|
— | |
|
|
Cub Scout Krenovs
Jeff Thunder de cloaked and emerged from deep lurk mode to send me this stab from the past, in response to the recent Cubbie thread. He graciously gave me permission to re-post it on the Wreck. Cub...
2
|
17 years ago
|
2 | |
|
|
Porter Cable #505 1/2 sheet sander
Hi all, I have a Porter Cable 505 half sheet sander and it has always been great to use. Lately it has been skating and jumping all over the place with just a little more than the weight of the sander...
1
|
17 years ago
|
1 | |
|
|
Bandsaw Vertical Drift! Help!!!
Hi, So I bought some 8/4 soft maple, with the thought that I could resaw it into 5/8" boards. I've got a 3 TPI 3/4" blade on my 14" Grizzy G0555. I went to resaw, and I found that the blade was...
26
|
17 years ago
|
26 | |
|
|
Seeking Ideas on Trim
I plan to pull up carpeting and expose HW floors, and at the same time replace my baseboards. I also want to redo the stairway end-cap (I believe there is a proper name for it, but I don't know what...
2
|
17 years ago
|
2 |